Description

Main Features

Used for high-temperature equipment in metallurgy, aviation, power, and corrosion prevention, such as steel plant blast furnaces, hot air furnace exteriors, high-temperature chimneys, flues, high-temperature hot air pipes, heaters, and heat exchangers.

Product Description

This product is a single-component coating consisting of organic silicon resin and heat-resistant pigments. It offers excellent adhesion, high heat resistance, withstanding temperatures up to 300°C to 600°C.

Physical Parameters

Color: Silver

Standard Dry Film Thickness: 30 micrometers (dry film), 75 micrometers (wet film)

Theoretical Coverage Rate: 8.3 m²/kg (at 30 micrometers dry film)

Actual Coverage Rate: Considering appropriate loss factors

Flash Point: 27±2°C

Application Instructions

Surface Preparation:

All surfaces to be coated should be clean, dry, and free of contaminants. Before painting, all surfaces should be assessed and prepared according to the ISO 8504:1992 standard. If there is grease, it should be cleaned with a solvent according to SSPC-SP1. Steel surfaces should be abrasive blasted to Sa2.5 (ISO 8501-1:1988), with a roughness of 30-70μm. If oxidation occurs on the steel surface after blasting but before coating, the surface should be reblasted to meet the specified visual standards. Manual rust removal methods can also be used to achieve Swedish rust standard St3 with a roughness of 30-70μm.

Thinner: Gold Brand #9 thinner

Application Methods: High-pressure airless spray, Air spray (with pressure pot), Brush/Roller

Thinning Ratios: 5-10%, 10-15%, 10-15%

Airless Spray: Nozzle Size: 0.46-0.58mm, Spraying Pressure: 15 MPa

Drying Time (23°C): ≤1 hour to touch, Full Cure ≤24 hours

Recoating Interval (with the same product): (Wet film thickness 60μm, relative humidity 80%)

5°C

20°C

30°C

Minimum

24 hours

16 hours

8 hours

The above data is for reference only. Actual drying times and recoating intervals may vary depending on film thickness, ventilation conditions, humidity, underlying paint, pre-assembly/disassembly requirements, and mechanical strength.

Tool Cleaning: Clean all tools with Gold Brand #9 thinner after use.

Safety: Handle this product with care. Before and during use, pay attention to safety information on the product label. Additionally, comply with safety regulations established by national or local government authorities. Avoid inhaling solvent vapors and direct contact with the paint on the skin and eyes. In case of skin contact, wash with appropriate cleanser, soap, and water. In case of eye contact, rinse thoroughly with water and seek medical attention. Take fire prevention, explosion prevention, and environmental protection measures. Only use this product in well-ventilated conditions.

Precautions

• Only apply this product in conditions where the temperature is above 5°C and application and curing can proceed normally. The maximum relative humidity during the curing process should be 80%, preferably between 40-60%. The application surface must be dry, clean, and have a temperature above the dew point to prevent condensation. Adequate ventilation should be provided during application in confined spaces and during drying. To prevent moisture condensation, the substrate surface temperature should be at least 3°C above the dew point, avoiding application in rainy, snowy, or foggy weather.
• Use the mixed paint within the recommended time frame, as exceeding this time can lead to gelation and render the paint unusable. The usable time may decrease with higher temperatures.
• Ensure that the coating is fully cured before applying the next coat.
• Drying time is influenced by temperature, humidity, and film thickness.
• Recoating intervals depend on environmental conditions. If the maximum recoating interval is exceeded, the surface must be roughened to ensure interlayer adhesion.
• Store the paint in a cool, dry, and well-ventilated warehouse, away from heat sources and direct sunlight.
• Applicators should wear appropriate protective gear, and the construction site and storage area should have firefighting equipment. No smoking or open flames should be allowed to prevent fires.
• This product is intended for professional use.

Packaging Size:

20kg per set

Shelf Life:

When stored in a cool, dry, and shaded area, the unopened product has a shelf life of twelve months (at 25°C).

Disclaimer:

The information provided in this product manual is based on our knowledge obtained in the laboratory and in practice. Statements in the manual are advisory in nature. Since product use is typically beyond our control, we provide no guarantee beyond the quality of the product itself. We reserve the right to modify this manual without prior notice.