Description

Main Feature

It has high compressive strength and is suitable for use as an intermediate paint for light and medium-load floors;

Diluted with water, green and environmentally friendly, with low VOC emissions.

Low odor and easy to construct

Detailed introduction

E336 water-based epoxy intermediate paint is a water-diluted epoxy intermediate paint, which is composed of water-based epoxy curing agent, liquid epoxy resin, deionized water and a small amount of additives.

Application scope

Floor applications in industrial plants, warehouses, underground parking lots, offices, home decoration floors, and places with high environmental requirements.

Product information

The material is divided into two components: A and B.

Component A yellow transparent liquid 18kg/barrel

Component B colorless transparent liquid 6kg/barrel

Packaging: Printed metal packaging drum. It is recommended to stack it in three layers when stacking.

Storage: Storage temperature 5-35℃, store in a cool, ventilated, dry warehouse; keep away from fire and heat sources and strictly prohibited from exposure to sunlight

Technical data

Status: Uniform, no lumps, no impurities

Bonding strength: ≥2.5MPa

Drying time: Surface dry: less than 6 hours

Hard work: less than 36 hours

(Temperature is 25℃, relative humidity is 50%)

Grassroots requirements

The compressive strength of the concrete floor should be ≥20Mpa, the tensile strength should be ≥1.5Mpa, and the flatness should be ±4mm/2m based on ruler. The base surface must be dry, clean, and free of oil and other pollution.

Construction Tips

Materials A and B should be used within 60 minutes after mixing. If the viscosity of the material is found to be significantly increased and it cannot be used anymore, it should be scrapped.

Construction should be stopped when the temperature falls below 10°C

The flatness and density of the substrate have a certain impact on the coating amount, drying time and recoating interval.

Construction Conditions

Ground base temperature: 10-35℃

Construction environment temperature: 10-35℃

Ground base moisture content: <8%

Relative humidity of construction environment: <80%

Construction methods/tools

Dilution: Dilute with water, the amount of water added is 20-30% of the paint volume.

Construction method: scraping

Tool: push knife

Instructions for use

Surface treatment: Before construction, dust, sand, cement laitance, grease, old coatings, etc. should be removed from the base surface and polished to form a rough surface. The capillary pores on the base surface should be opened, the floating dust on the surface should be cleaned, and water-based epoxy should be used. Primer seals the base surface.

Dosage: about 0.30㎏/㎡, one pass of 80-120 mesh sand and one pass of 400 mesh powder. There are big differences based on the flatness of the ground and the construction design plan.

Construction method: Mix the main agent and curing agent at a weight ratio of 3:1, and stir mechanically for 2 minutes until the mixture becomes uniform and creamy. Then add 30% water to dilute and stir evenly. Add quartz sand or quartz powder and stir evenly before scraping.

Sand adding ratio

80-120 mesh quartz sand paint: quartz sand=1:1.5-2 (mass ratio)

200-400 mesh quartz powder paint: quartz powder = 1:0.8-1 (mass ratio)

Note: The amount of paint is the total amount of components A and B, excluding water added later.

Precautions

For safe use of the product, please request the product safety data sheet (MSDS) from the manufacturer.

Construction workers should strengthen safety protection when using this product, and the construction environment should be kept ventilated.

For any unspecified matters, please contact local distributors or directly contact the factory.

First-aid

Skin Contact: Wash with plenty of water and remove contaminated clothing and shoes

Eye contact: Rinse with running water or saline, seek medical attention in serious cases

Inhalation: Move to fresh air and keep respiratory tract open. If you feel unwell, seek medical advice.

Ingestion: Clean up leftovers in the mouth, induce vomiting, seek medical attention

Fire-fighting measures

Hazardous characteristics: non-flammable

Hazardous combustion products: carbon monoxide, carbon dioxide, etc.

Fire extinguishing methods and fire extinguishing media: Move the container from the fire scene to an open area as much as possible

Fire extinguishing media: dry powder, sand